Hypertec Network Card HYNEU010001 User Manual

USB 10base-T Ethernet Adapter  
HYNEU010001  
USER GUIDE  
Information in this document is subject to change without notice. All  
rights reserved. All brand names are registered trademarks of their  
respective companies.  
 
small office/home office (SOHO) environments.  
The Hypertec USB Ethernet plugs directly into the USB port located on  
the back of most modern computers, and eliminates the need to open the  
PC when adding an Ethernet connection.  
About the Universal Serial Bus (USB)  
Universal Serial Bus (USB) is a peripheral bus standard developed by  
PC and telecom leaders such as Compaq, DEC, IBM, Intel, Microsoft,  
NEC and Northern Telecom. PCs equipped with USB allow computer  
peripherals once installed on a system to be automatically configured as  
soon as they are physically attached without the need to reboot or run  
setup. Thus, USB brings true "out of the box" plug-and-play to computer  
peripherals. USB features fast I/O transfer rate of 12 Mbits/s and allows  
up to 127 devices to run simultaneously on one computer.  
Typically, there are several connectors on the back of a computer, each  
of which accepts a specific kind of device connector and cable. As a  
result, a maze of confusing cables can be found at the back of a  
computer when a full range of peripherals are attached, USB eliminates  
the need for variety of connectors and cables because a single, standard  
type of connector and cable is used for every peripheral device,  
connected in a "daisy chain' fashion.  
 
running  
Full Windows 98 support  
Supports the energy-saving and suspend-and-resume functions  
No external power supply is required  
RJ-45 female connector for Ethernet 10Base-T connection  
Dual LED status indicators for Link and Activity  
Ideal for home PC users  
Self diagnostics at initialisation  
HyperNet USB 10baseT Ethernet Adapter  
 
Remove the entire contents of the HyperNet USB Ethernet adapter  
package and verify that the following items have been included and none  
have been damaged during shipment:  
·
·
·
HyperNet USB Ethernet Adapter  
3.5" USB Ethernet Software driver diskette  
Installation Guide  
Connecting the USB Ethernet Adapter  
The USB Ethernet adapter hardware installation is a simple two-step  
process:  
1. Connect the USB Type A plug into the USB port on the computer.  
2. Attach a UTP or STP network cable (Category 3 or 5) to the RJ-45  
connector located on the other side of the adapter.  
The UTP or STP network cable also needs to be connected to a suitable  
10base-T compatible HUB device.  
Disconnecting the USB Ethernet Adapter  
When you have finished working with the USB Ethernet adapter, you  
can disconnect it from the computer by pulling the Type A plug from  
your computer.  
Note: Upon reconnecting the USB Ethernet adapter to the computer,  
allow approximately up to one minute for the system to recognise the  
reconnected adapter.  
 
Figure 1.  
3.  
Choose Search for the best drivers for your device (see figure 2)  
and click Next.  
Figure 2.  
 
Figure 3.  
6. Click Next to confirm driver selection (see figure 4)  
Figure 4.  
 
Figure 5.  
8. Click finish to complete network installation, remove the driver  
disk and click Yes to restart the computer (see figure 6)  
Figure 6.  
If at any time during installation you experience difficulties, please  
contact Hypertec Technical Support on +44 1488 686844  
(01488 686844 in the UK).  
 
Data Transfer Rate:  
10 Mbits/sec  
Ethernet Connector:  
Unshielded RJ-45 female connector  
Ethernet LED's:  
Green - Activity  
Yellow - Link  
Weight:  
1.85 oz, 51gr. (Including the USB cable)  
Physical Dimensions:  
Length - 2.28" (58 mm)  
Width - 1.69" (43 mm)  
Thickness - 0.98" (25 mm)  
Operating Voltage:  
5 V (powered via the USB connection)  
Power Consumption:  
80mA (Active)  
120mA (max)  
Operating Temperature:  
0°-70°C  
Operating Humidity:  
0% - 90% non-condensing  
Certifications:  
FCC Part 15, Subpart B class B  
 
become the property of Hypertec.  
This warranty applies only to the original registered end user purchaser  
of the product and does not include service to repair damage resulting  
from accident, disaster, misuse, abuse or non-Hypertec modification of  
the product.  
Additional components installed by the dealer or end user are not  
covered by this warranty. Apart from the above, no warranty is  
expressed or implied, including warranty of merchantability or warranty  
of fitness for use for a particular purpose.  
The liability of Hypertec is limited to the repair or replacement of the  
product with a functionally equivalent or better product. Hypertec is not  
liable for any accidental, general, special, exemplary or consequential  
damages resulting from any product failure, even if Hypertec has been  
advised of the possibility of such damages.  
Hypertec Limited  
Units 1-3 Station Road  
Hungerford, Berkshire RG17 0DY  
Ph: +44 (0)1488 686844  
Fax:  
Web:  
Email:  
+44 (0)1488 686845  
 

GPX Stereo System HM1836 User Manual
Graco Crib ISPP003AA User Manual
Grundig Coffeemaker KM4062 User Manual
Haier Washer Twin tub Washing User Manual
Honeywell Air Cleaner F120 User Manual
Hotpoint Microwave Oven BD32 User Manual
HP Hewlett Packard Water Dispenser 8591A User Manual
Huffy Fitness Equipment 110 816R019 User Manual
Husqvarna Lawn Mower 233RJ User Manual
IBM Printer S544 5361 01 User Manual