OWNER’S MANUAL
Model Number H346SL
Product No. 960 73 00-12
(MFG. ID. No. 96073001200)
46 Inch Mower
Grass Catcher
• Assembly
• Operation
• Customer Responsibilities
• Repair Parts
532413532 03.05.07 BY
Printed in U.S.A.
SAFETY RULES
Safe Operation Practices for Ride-On Mowers
machine. Repair, if necessary, before restarting.
IV. TOWING
•
•
Nevermakeanyadjustmentsorrepairswiththeengine
running.
•
Tow only with a machine that has a hitch designed for
towing. Do not attach towed equipment except at the
hitch point.
Check grass catcher components and the discharge
guard frequently and replace with manufacturer's rec-
ommended parts, when necessary.
Mower blades are sharp. Wrap the blade or wear
gloves, and use extra caution when servicing them.
Check brake operation frequently. Adjust and service
as required.
Maintain or replace safety and instruction labels, as
necessary.
•
•
•
•
Follow the manufacturer's recommendation for weight
limits for towed equipment and towing on slopes.
Never allow children or others in or on towed equip-
ment.
•
•
•
On slopes, the weight of the towed equipment may
cause loss of traction and loss of control.
Travel slowly and allow extra distance to stop.
V. SERVICE
SAFE HANDLING OF GASOLINE
To avoid personal injury or property damage, use extreme
careinhandlinggasoline. Gasolineisextremelyflammable
and the vapors are explosive.
•
Be sure the area is clear of bystanders before operat-
ing. Stop machine if anyone enters the area.
Never carry passengers.
•
Extinguish all cigarettes, cigars, pipes, and other
sources of ignition.
•
•
•
•
Use only approved gasoline container.
Never remove gas cap or add fuel with the engine
running. Allow engine to cool before refueling.
Never fuel the machine indoors.
Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while back-
ing.
Nevercarrychildren,evenwiththebladesshutoff. They
may fall off and be seriously injured or interfere with
safemachineoperation.Childrenwhohavebeengiven
rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over
by the machine.
Keepchildrenoutofthemowingareaandinthewatchful
care of a responsible adult other than the operator.
Be alert and turn machine off if a child enters the
area.
Before and while backing, look behind and down for
small children.
Mow up and down slopes (15° Max), not across.
Be alert and turn machine off if a child enters the
area.
•
•
Never store the machine or fuel container where there
is an open flame, spark, or pilot light such as on a water
heater or other appliances.
•
•
•
Never fill containers inside a vehicle or on a truck or
trailer bed with plastic liner. Always place containers
on the ground away from your vehicle when filling.
Removegas-poweredequipmentfromthetruckortrailer
and refuel it on the ground. If this is not possible, then
refuel such equipment with a portable container, rather
than from a gasoline dispenser nozzle.
Keep the nozzle in contact with the rim of the fuel tank
orcontaineropeningatalltimesuntilfuelingiscomplete.
Do not use a nozzle lock-open device.
If fuel is spilled on clothing, change clothing immedi-
ately.
Never overfill fuel tank. Replace gas cap and tighten
securely.
•
•
•
•
•
•
•
•
•
•
Choose a low ground speed so that you will not have
to stop or shift while on the slope.
Avoid starting, stopping, or turning on a slope. If the
tires lose traction, disengage the blades and proceed
slowly straight down the slope.
If machine stops while going uphill, disengage blades,
shift into reverse and back down slowly.
Do not turn on slopes unless necessary, and then, turn
slowly and gradually downhill, if possible.
GENERAL SERVICE
•
Never operate machine in a closed are.
•
Keep all nuts and bolts tight to be sure the equipment
is in safe working condition.
•
•
Never tamper with safety devices. Check their proper
operation regularly.
Keep machine free of grass, leaves, or other debris
build-up. Cleanoilorfuelspillageandremoveanyfuel-
soaked debris. Allow machine to cool before storing.
If you strike a foreign object, stop and inspect the
•
•
•
CONGRATULATIONS on your purchase of a new Grass Catcher. It has been designed, engineered and manufactured to
give you the best possible dependability and performance.
Should you experience any problems you cannot easily remedy, please contact your nearest authorized service center/
department. They have competent, well trained technicians and the proper tools to service or repair this unit.
Please read and retain this manual. The instructions will enable you to assemble and maintain your Grass Catcher properly.
Always observe the "SAFETY RULES".
TABLE OF CONTENTS
SAFETY RULES ...................................................................2-3
ASSEMBLY...........................................................................5-8
OPERATION ............................................................................ 8
CUSTOMER RESPONSIBILITIES........................................... 9
STORAGE................................................................................ 9
REPAIR PARTS ............................................ Center of Manual
3
KNOW YOUR GRASS CATCHER
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE ASSEMBLING OR OPERATING YOUR GRASS
CATCHER. Compare the illustrations with the carton contents to familiarize yourself with the parts before starting the
assembly. Study the operating instructions and safety precautions thoroughly to insure proper functioning of your Grass
Catcher and to prevent injury to yourself and others. Save this manual for future reference.
The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe
eye damage. Always wear safety glasses or eye shields before starting your tractor and while mowing.
We recommend a wide vision safety mask for over the spectacles or standard safety glasses.
COMPLETE BAGGER MUST BE IN PLACE BEFORE OPERATING MOWER
UNPACKING INSTRUCTIONS
TOOLS REQUIRED FOR ASSEMBLY
•
•
Remove all parts and packing materials from carton.
(1) 9/16" Wrench
Check carton contents against list. Be sure all parts
are there.
PARTS IDENTIFICATION:
SHOULDER
BOLTS
CARTON CONTENTS:
(1) Support Assembly
(1) Cover Assembly
(2) Shoulder Bolts
(1) Retainer Spring
SUPPORT
ASSEMBLY
(3) Containers
(1) Upper Chute
(1) Lower Chute
FULL
COVER
ASSEMBLY
BAG
INDICATOR
RETAINER SPRING
CHUTE LATCH
UPPER
CHUTE
LOWER
CHUTE
ATTACHING
STRAPS
GRASS
CATCHER
CONTAINERS
LOWER
CHUTE
NOTE: When right hand (R.H.) and left hand (L.H.) are mentioned in this manual, it means when you are seated on the
tractor, in the operator's position.
CAUTION: BEFORE ASSEMBLING GRASS CATCHER TO TRACTOR:
•
•
•
•
•
•
Depress clutch/brake pedal fully and set parking brake.
Place gearshift/motion control lever in "NEUTRAL" position.
Place attachment clutch in "DISENGAGED" position.
Turn ignition key "OFF" and remove key.
Make sure the blade and all moving parts have completely stopped.
Disconnect spark plug wire from plug and place where it cannot come in contact with plug.
4
ASSEMBLY
MOUNTING COVER ASSEMBLY TO
SUPPORT ASSEMBLY (See Fig. 2)
NOTE: For ease of assembly, you may wish to obtain
the assistance of another person for mounting cover as-
sembly to tractor.
BAGGER SUPPORT ASSEMBLY
(See Fig. 1)
1. Remove and discard the upper bolt on both sides of
thedrawbar. Usingthesameholes, installtheshoulder
bolts supplied and tighten securely.
2
1
2. Align support assembly pin with hole in drawbar and
hang assembly over the shoulder bolts.
1. Lift cover and align cover brackets with support
assembly tubes.
3. Besuresupportassemblyisseatedproperlyandsecure
with retainer spring supplied.
2. Slide cover assembly down onto the support tubes.
REMOVE AND DISCARD
UPPER BOLTS AND INSTALL
SHOULDER BOLTS SUPPLIED
COVER
ASSEMBLY
SUPPORT
ASSEMBLY
FIG. 2
SUPPORT
ASSEMBLY
3064
PIN
DRAWBAR
RETAINER
SPRING
FIG. 1
5
CONTAINER MOUNTING (See Fig. 3)
LOWER CHUTE - MOWER WITH
MOUNTING TAB (See Fig. 4)
3
4
1. Install one container to left side first. Install another
container to center position and one in right position.
NOTE: Left edge of right container should always overlap
right edge of left container at center supports.
2. Close cover and lock latches over center support
tubes. To lock and release latches, pull back on latch
handles.
1. Raise and hold deflector shield in upright position.
2. Place slot in lower chute over mounting tab on mower
and position lower chute over mower opening as
shown.
3. Hook rear latch into flange hole on back of mower.
4. Hook front latch into flange hole on front of mower.
CAUTION: Do not remove deflector shield
from mower. Raise and hold shield when
attaching lower chute and allow it to rest
on chute while in operation.
COVER LATCH
HANDLES
CENTER
SUPPORT
TUBES
DEFLECTOR SHIELD
HINGE BRACKET
CONTAINER
HANDLE
FIG. 3
DEFLECTOR SHIELD
MOUNTING
TAB
REAR LATCH
FRONT LATCH
FIG. 4
6
UPPER CHUTE (See Figs. 5A and 5B)
LEVEL MOWER
5
6
1. Lower mower to its lowest cutting position.
2. Assemble upper chute by inserting curved end into
hole in back of cover.
•
Be sure mower is properly leveled for best mower
performance. See your tractors owner's manual for
instructions
TIP: Holding upper chute as shown and twisting while
installing in cover will help keep the rubber seal in place.
NOTE: Handle carefully so as not to damage full bag indi-
cator.
COVER
UPPER
CHUTE
FIG. 6A
3. Push in and turn upper chute until it is in line with lower
chute.
4. Align the bosses on lower chute with alignment slots
on upper chute and slide together.
5. Secure with rubber latch by hooking hole in latch over
latch pin.
FULL BAG
INDICATOR
COVER
UPPER
CHUTE
HANDLE
LATCH PIN
RUBBER
LATCH
LOWER
CHUTE
ALIGN-
MENT
SLOT
BOSSES
FIG. 6B
7
OPERATION
•
Your bagger is equipped with a full bagger indicator.
TIPS FOR IMPROVED BAGGING
OPERATION:
Movement of the wheel increases as the bags fill. The
wheel will be spinning fastest just before the bags fill
completely. When the wheel stops, it indicates that the
bags are full and the chutes have become clogged.
Follow the mower operation instructions in your tractor
owner's manual.
When operating your grass catcher on a lawn where grass
and leaf bagging equipment has not been used, you are
picking up thatch and debris that has accumulated for long
periods of time. The amount collected and the total time
of operation may be greater than you will experience with
regular use of your grass catcher.
NOTE: To help prevent clogging of chutes, check/empty
bagswhenthewheelisspinningfast. Experiencewillteach
you the best time to empty the bags.
Care should be taken not to damage the parts and that
the wheel spins freely at the beginning of each use.
•
If the grass catcher fails to pick up cut grass or leaves,
it is an indication that clogging has occurred in the
system or that the grass catcher containers are full.
Usually this is indicated by the stopped movement of
the full bagger indicator.
•
•
Always run throttle at full speed when bagging.
Select a gear low enough to give good mower cutting
performance, good quality cut and good bagging
performance.
NOTE: It may be necessary to overlap width of cut to suit
your conditions.
a. Disengage blades, shift into neutral, engage the
parking brake and stop the engine.
•
If grass is extremely tall, it should be mowed twice. The
first time relatively high, the second time to desired
height.
- Raise seat. Unlatch and raise cover.
- Slide out containers and dispose of clippings .
- Replace containers, close cover, and latch.
b. Unlatch chutes and check for clogging.
- Remove all debris in chutes.
•
•
Use left hand side of mower for trimming.
Plastic trash bags can be inserted inside grass catcher
containers for ease of debris disposal. To remove the
plastic trash bags when full:
a. Disengage blades, shift into neutral, engage the
parking brake and stop the engine.
- Reassemble and latch chutes
c. Checktoinsurefullbaggerindicatorhasnotbecome
clogged.
b. Raise seat. Unlatch and raise cover.
- The air passage hole must be clear of debris.
Gentlyinsertasmalltwigorwireintopassageway
to clear.
c. Remove one container at a time by grasping
container handles and pulling toward the rear, off
of the tube rails.
d. With the container resting on the ground, close
and secure the top of the plastic lawn bag.
CAUTION
e. Tip the container on its side and slide the filled bag
from the container.
f. Install a new plastic lawn bag with the edges of
the bag draped over upper lip of the container.
g. Repeat for other containers.
h. Reinstall containers making sure right container
overlaps left container at center supports.
j. Closecoverandsecurelatchesovercentersupport
tubes.
Avoid cutting wet grass or in the morning while the dew
is still heavy. Grass clippings collected under these
conditions tend to be sticky and adhere to the walls of
the flow path causing clogging.
• Do not operate mower with grass catcher
partially installed.
• Disengage blades and stop engine before
leaving tractor seat to empty containers,
unclogging chutes, etc.
• Close cover before starting.
• Disengage mower when crossing driveways
or gravel surfaces and other areas where
thrown objects could be a hazard.
• Do not attempt to vacuum up cans or other
potentially hazardous projectiles.
•
8
CUSTOMER RESPONSIBILITIES
GENERAL RECOMMENDATIONS
CAUTION: Grass catcher components
are subject to wear, damage and
deterioration, which could expose
moving parts or allow objects
to be thrown. Frequently check
components and replace with
manufacturer's recommended parts,
when necessary.
Always observe safety rules when performing any main-
tenance.
•
•
Before each use check for loose fasteners.
Clean unit thoroughly after each use.
BLADE CARE
Forbestresultsmowerbladesmustbekeptsharp. Replace
bent or damaged blades.
•
See BLADE CARE instructions in your tractor owner's
manual.
CAUTION:BEFOREPERFORMINGANY
MAINTENANCE,SERVICEORADJUST-
MENTS:
•
•
•
Depress clutch brake pedal fully and
set parking brake.
Place gearshift/motion control lever in
"NEUTRAL" position.
Placeclutchcontrolin"DISENGAGED"
position.
Turn ignition key to "OFF" position.
Make sure blades and all moving parts
have completely stopped.
Disconnect spark plug wire(s) from
spark plug(s) and place wire where it
cannot come in contact with plug.
STORAGE
When grass catcher is to be stored for a period of time,
clean it thoroughly, remove all dirt, grass, leaves, etc. Store
in a clean, dry place.
•
•
CAUTION: Donotleavegrassinbagger
containers. Emptycontainersaftereach
useandbeforestoring. Failuretodoso
mayresultinspontaneouscombustion
which could develop into a fire.
•
9
REPAIR PARTS
GRASS CATCHER - MODEL NUMBER H346SL (PRODUCT NO. 960 73 00-12)
4
5
6
7
8
10
12
13
9
2
9
11
14
2
18
20
15
38
38
20
34
37
15
9
20
12
14
3
20
33
26
32
31
35
33
31
28
29
29
30
KEY PART
NO. NO.
KEY PART
NO. NO.
DESCRIPTION
DESCRIPTION
2
3
532069180 Nut, Crownlock #10-24
532127533 Screen, Cover
22
23
24
25
26
27
28
31
32
33
34
35
38
39
29
30
532133235 Spacer, Cover
532132983 Spring, Cover R.H. (gray)
532179745 Bracket, Lock
873800400 Locknut
532124670 Spring, Retainer
872140405 Bolt
532198364 Support Assembly
532174083 Plug, Tubing End
532176990 Bagger, Frame
532192786 Pin, Hinge
532192550 Gasket, Cover
532400226 Container
4
5
532193010 Cover Assembly (Includes 34 & 37)
532411397 Chute, Upper
6
7
8
9
10
11
12
13
14
15
18
20
21
818021008 Screw, Special #10-14x1/2
532130933 Full Bag Indicator
532087175 Screw, #10-24 x 1-1/8
819061216 Washer 3/16x3/4x16 Ga.
532007206 Spacer, Split
532060867 Nut, Acorn #10-24
810071000 Washer, lock
532109808 Latch, Chute
532125004 Nut, Weld
532160793 Latch, Hook
532405455 Chute, Lower
532130895 Latch Handle, Cover
532155042 Strip, Reinforcement
532176997
532165898 Spring, retainer
Shoulder bolt, self tapping
871081010 Screw #10-24 x 5/8
532132796 Spring, Cover L.H. (black)
10
starter ropes and tiller tines;
(2) Natural discoloration of material due to ultraviolet light;
WARRANTY STATEMENT
(3) Engine and drive systems not manufactured by Husqvarna; these items are covered by the respective manufacturer’s
warranty as provided in writing with the product information supplied at the time of purchase; all claims must be sent to the
appropriate manufacturer;
SECTION 1: LIMITED WARRANTY
(4) Lawn and garden attachments are covered by a third party which gives a warranty, all claims for warranty should be sent
to the manufacturer,
(5) Commercial or consumer mowing decks with sand abrasion damage.
(6) Emission Control System components necessary to comply with CARB-TIER II and EPA regulations which are
manufactured by third party engine manufacturer.
Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from
defects in material and workmanship from the date of purchase for the “Warranty Period” of the product as set forth below:
Lifetime Warranty (Parts and Labor): All tiller tines and trimmer shafts against breakage. Proof of purchase required.
Lifetime Warranty (“PARTS ONLY” after initial warranty expiration): Ignition coils and modules on handheld product.
Proof of purchase required.
WARRANTY SCHEDULE FOR TURF CARE Equipment - Zero Turn Riders
SECTION 4: EXCEPTIONS AND LIMITATIONS
This warranty shall be inapplicable to defects resulting from the following:
(1) Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust, corrosion, or any
adverse reaction due to incorrect storage or use habits;
(2) Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruction sheet furnished
by Husqvarna;
(3) Alterations or modifications that change the intended use of the product or affects the product’s performance, operation,
safety, or durability, or causes the product to fail to comply with any applicable laws; or:
(4) Additional damage to parts or components due to continued use occurring after any of the above.
(New warranty applies to units sold after August 1, 2005. Also applies to units factory-equipped with R.O.P.S.
EZ Zero Turn Riders: 3 year consumer warranty or 600 hours of use (when used solely at the owner’s residence.)
EZ & MZ Zero Turn Riders: 1 year commercial warranty or 600 hours of use.
iZ, LZ & BZ Zero Turn Riders: 5 year consumer warranty or 1,500 hours of use.
iZ, LZ & BZ Zero Turn Riders: 5 year commercial warranty or 1,500 hours of use.
3 Year or 1,500 Hour Commercial Use Warranty: spindles on zero turn riders, hydraulic pumps and wheel motors.
Warranty Schedule for Turf Care Walk Behind Units - W, WG & WH Zero Turn Riders - 3 year consumer and commercial
warranty. New warranty applies to units sold after August 1, 2005. Also applies to units factory-equipped with R.O.P.S.
2 Year COMMERCIAL and CONSUMER Warranty: all Husqvarna ground-engaging commercial equipment.
WARRANTY SCHEDULE FOR CONSUMER TURF CARE EQUIPMENT:
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE
PURCHASER. HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR
BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THESE PRODUCTS EXCEPT TO THE EXTENT
PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ON THESE PRODUCTS IS LIMITED IN DURATION TO THE WARRANTY PERIOD AS
DEFINED IN THE LIMITED WARRANTY STATEMENT. HUSQVARNA RESERVES THE RIGHT TO CHANGE OR
IMPROVE THE DESIGN OF THE PRODUCT WITHOUT NOTICE, AND DOES NO T ASSUME OBLIGATION TO UPDATE
PREVIOUSLY MANUFACTURED PRODUCTS.
2 Year Consumer Warranty: Automatic mower, all Residential Zero Turn Riders, all lawn, yard and garden tractors, all
noncommercial walk behind mowers, tillers, snow blowers, electrical products and power-assist collection systems for
noncommercial, nonprofessional, noninstitutional or nonincome producing use, except as herein stated. All consumer
product use must have been limited to the owner’s residence.
WARRANTY SCHEDULE FOR CONSUMER FOREST & GARDEN EQUIPMENT:
2 Year Consumer Warranty: all consumer chain saws, trimmers, brushcutters, clearing saws, handheld blowers, backpack
blowers, hedge trimmers, and electrical products for noncommercial, nonprofessional, noninstitutional or nonincome
producing use, except as herein stated. All consumer product use must have been limited to the owner’s residence.
2 Year or 2,000 Hour Powertrain & 1 Year or 1,000 Hour Body Warranty: Husqvarna Utility Vehicles.
1 Year Warranty: Power cutters, stump grinder, pole pruners and pole saws for non-commercial, non-professional,
noninstitutional, non-municipality or non-income producing use. All 300 series trimmers, brushcutters, clearing saws,
hovering trimmers, stick edgers, backpack blowers, hand held blowers, hedge trimmers, power-assist collection systems for
commercial, institutional, professional or income producing purposes or use.
1 Year Conditional Component Warranty: Chain saw crankshafts for commercial/professional use (parts and labor).Saw
must be operated with Husqvarna XP 2 cycle oil.
90 Day Commercial Warranty: Automatic mower, chain saws, 100 series trimmers, power cutters, stump grinders, pole
saws, pole pruners, snow throwers, model series 580 & 600 walk-behind mowers, or any Husqvarna product used for
commercial, institutional, professional, municipality or income producing purposes or use except as otherwise provided herein.
Batteries: 1 year prorated limited warranty with 100% replacement during the first 6 months.
Rental Warranty: 90 days on all applicable professional equipment reference warranty time period charts
located in the back of the Retailer Warranty Policy & Procedure Manual.
Husqvarna Safety Apparel carries a 90-day warranty from the date of the customer’s original purchase for defects in
material and workmanship. Normal wear, tear or abuse is not covered under warranty. Product must be returned to Charlotte
with a warranty claim form. All care and maintenance instructions must be followed as stated by the manufacturer on the
care label. The fit of the protective apparel/boot is not covered under warranty.
Some states do not allow the exclusion of incidental or consequential damages, or limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state.
SECTION 5: CUSTOMER RESPONSIBILITIES
The product must exhibit reasonable care, maintenance, operation, storage and general upkeep as written in the
maintenance section of the Owner’s/Operator’s manual. Should an operational problem or failure occur, the product should
not be used, but delivered as is to an authorized Husqvarna retailer for evaluation. Proof of purchase, as explained in
section 6, rests solely with the customer.
SECTION 6: PROCEDURE TO OBTAIN WARRANTY CONSIDERATION
It is the Owner’s and Retailer’s responsibility to make certain that the Warranty Registration Card is properly filled out and
mailed to Husqvarna Forest & Garden Company. This card should be mailed within ten (10) days from the date of purchase
in order to confirm the warranty and to facilitate post-sale service.
Proof of purchase must be presented to the authorized Husqvarna retailer in order to obtain warranty service. This proof
must include date purchased, model number, serial number, and complete name and address of the selling retailer.
30 Day Warranty: Replacement parts, accessories including bars and chains, tools and display items. Emission control
system components necessary to comply with CARB-TIER II and EPA regulations, except for those components which are
part of engine systems manufactured by third part engine manufacturers for which the purchaser has received a separate
warranty with product at time of purchase.
To obtain the benefit of this warranty, the product believed to be defective must be delivered to an authorized Husqvarna
retailer in a timely manner, no later than thirty (30) days from date of the operational problem or failure. The product must be
delivered at the owner’s expense. Downtime, pick-up and delivery charges are not covered by this warranty. An authorized
Husqvarna retailer can be normally located through the “Yellow Pages” of the local telephone directory or by calling 1-800-
HUSKY62 for a retailer in your area.
SECTION 2: HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY
Husqvarna will repair or replace defective components without charge for parts or labor if a component fails because of a
defect in material or workmanship during the warranty period.
HUSQVARNA
7349 Statesville Road
Charlotte, NC 28269
2008
SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY
The following items are not covered by this warranty:
(1) Normal customer maintenance items which become worn through normal regular use, including, but not limited to, belts,
blades, blade adapters, bulbs, clutches, clutch drums, filters, guide bars, lubricants, rewind springs, saw chain, spark plugs,
|