Failure to follow these warnin
instructions could result in se
Recliner Swing
OWNER’S
MANUAL
Model No.
Serial No.
Dear Customer,
Please fill in the model
and serial numbers
above from the label
beneath the motor
of your new swing.
Never leave child unattended.
Always keep your child in view.
A
s
Models 1131, 1132, 1141
Congratulations on your purchase of a
Graco® swing!
Graco is the recognized leader in the
design and manufacture of quality baby
swings. We believe your new Graco®
swing is a wise choice, promising many
hours of enjoyment for your baby.
Before using your swing, please take a
few minutes to read this Owner’s Manual.
The short time you spend reading these
instructions will help you use your
swing properly.
Strings can cause strangulation.
DO NOT place items with a string
around your child’s neck, such as
hood strings or pacifier cords. DO
NOT suspend strings over swing
or attach strings to toys.
STRANGULATION HA
DO NOT place swing
location where there a
such as window blind
drapes, phone cords,
Please save your Owner’s Manual
for future use.
FR
sc
re
THIS PRODUCT REQUIRES ADULT ASSEMBLY.
FOLLOW ASSEMBLY INSTRUCTIONS CAREFULLY.
If you experience any difficulties, please contact the
Customer Service Department.
Customer Satisfaction
DO
Our goal is to make every product the best it
can be! We are also committed to supporting our
products after purchase. If you would like to speak
to Graco about your product, please contact our
Customer Service Department at 1-800-345-4109
Our knowledgeable staff will be ready to answer
any questions you may have concerning parts, use,
or maintenance. When you call, please have the
model and serial numbers ready so your call may
be processed quickly and efficiently.
EX
fa
DO NOT USE SWING without the seat cover.
DISCONTINUE USING YOUR SWING should it become
damaged or broken.
DO
ho
RE
m
cy
TO
de
© 1999 Graco 135-1-99 IS2131
2
PARTS LIST
CHECK that you have all the parts listed
below BEFORE assembling your swing.
If any parts are missing, call
Customer Service at 1-800-345-4109 or visit
e warnings and the assembly
sult in serious injury or death.
Tools required: Screwdriver and wrench
(wrench included)
OR
Vinyl seat cover with
2 plastic fasteners
Cloth seat cover
Avoid serious injury from falling or
sliding out. Always use seat belt.
Motor
unit
Plastic seat
Hanger
tube (2)
Seat belt
and buckle
Short machine
screw (2)
Seat wire
GULATION HAZARD:
place swing in any
where there are cords,
window blind cords,
phone cords, etc.
DO NOT use if child weighs over
25 pounds (11.3 kg) or becomes
too active to safely use the swing.
Wrench
Acorn nut (4)
CARE AND MAINTENANCE
Plastic leg brace (2)
FROM TIME TO TIME CHECK YOUR SWING for loose
screws, worn parts, torn material or stitching. Replace or
repair parts as needed. Use only Graco® replacement parts.
Knob end
Dimple
Round end
Upper leg section (4)
DO NOT STORE SWING with motor fully wound.
EXCESSIVE EXPOSURE TO SUN OR HEAT could cause
fading or warping of parts.
Wire end
Round end
Lower leg section (4)
Leg tip (4)
DO NOT STORE SWING in any location which can become
hot, such as a car trunk or attic. Plastic parts may warp.
REMOVABLE CLOTH SEAT COVER (on certain models)
may be machine washed in lukewarm water on delicate
cycle and drip-dried. NO BLEACH.
Bead (2)
Toy bar
Ring (3)
TO CLEAN SWING FRAME, use only household soap or
detergent and warm water. NO BLEACH.
3
4
Step 3.
Attaching the Seat Belt
From the inside of the seat,
press the two plastic fasteners
through the holes in the vinyl
cover into the holes in the
plastic seat.
Step 1.
Thread the free end of the seat
belt through the belt retainer as
shown.
If holes in vinyl are not fully
open, push fasteners through
vinyl with enough force to open
the holes.
Step 2.
Open buckle by squeezing
sides of buckle to release.
Step 4.
Fold cover around bottom of
seat.
Step 3.
Cloth Seat Cover
(on certain models):
(No plastic fasteners are
included with cloth seat cover
models.)
Thread belt through the buckle
as shown. CHECK to make
sure that the belt is threaded
correctly by pulling on the seat
belt. The belt should not slip
through the buckle.
Step 1.
Slide the pocket of the cloth
cover over the top of the seat
as shown.
Attaching the Seat Cover—2 Options
Your swing will have EITHER a vinyl or cloth seat cover.
Follow the appropriate instructions below.
Vinyl Seat Cover
Step 2.
(on certain models):
Push both ends of the seat belt
through the slots in the cloth
cover, and pull the belt through.
Step 1.
Slide pocket at top of vinyl
seat cover over the seat back.
Step 3.
Push the plastic clip under
one side of the seat as shown.
Repeat on other side.
Step 2.
Push both ends of the seat
belt through the slots in the vinyl
cover, and pull the belt through.
If slots in vinyl are not fully
open, push ends of buckle
through vinyl with enough force
to open the slots.
Step 4.
Pull the fabric out at the leg
openings.
7
8
Installing the Toy Bar
Starting Swing
R
In
Be sure all parts are securely
fastened together before
using the swing.
Step 1.
Co
inc
Yo
sw
Place the two beads and three
rings on the bar. The suggested
order is ring-bead-ring-bead-
ring. (Once the toy bar is on
the tray, the order cannot be
changed.)
Step 1.
Open the seat belt. Place baby
in the seat. (If your child is very
small, you may want to use
rolled-up blankets as a prop.)
P
M
Pl
Si
Si
Fr
Vi
Cl
Se
Ha
Pl
Ad
Up
Lo
Le
To
* O
Step 2.
Snap the bar (one end at a
time) into the two “U”-shaped
holes located on the top front
of the tray. CHECK that bar is
securely attached by pulling
up on the bar.
Step 2.
Fasten the seat belt. Adjust
belt as needed to get a snug fit
around your child.
Do not depend on the tray alone to hold
your baby. Always secure your baby with the seat belt
when your child is in the swing.
Step 3.
Finished assembly will look like
illustration.
Step 3.
Wind crank clockwise. Swing is fully wound when you hear
a clicking sound while winding.
Make sure toys are properly assem-
Step 4.
bled before and during use. Do not tie other toys
or objects onto the swing toys. If child is able to
remove the toy bar from the tray, discontinue use.
PUSH SWING SEAT TO START. BE SURE YOU PUSH IT
UP HIGH ENOUGH FOR THE MOTOR TO GET A GOOD
START.
Reclining the Seat Back
Special features on certain models:
Some models have a “time-remaining” indicator on the right
side of the swing faceplate. After you finish winding, it will
show you the remaining swing time. It also indicates when
you need to rewind the motor.
The seat has two positions,
upright and reclined.
To recline the seat, first lift
the seat wire, then pull the
back of the seat downward.
Some models have a switch on the left side of the swing
faceplate to adjust the height of the swinging motion.
Observe the swinging motion for a minute before changing
the setting. It takes time for your swing to adjust to a new
setting.
For the upright position, just
pull forward on the top of the
seat.
For a lower ride, push the control switch toward “low.”
•
For a higher ride, push the control switch toward “high.”
•
NOTE: Seat may be stopped any time motor
is running without damaging motor. To restart,
push swing.
135-1-99 IS2132
9
10
Replacement Parts
Instructions for ordering swing parts:
Complete form below. Your swing model number MUST be
included on the form to ensure proper replacement parts.
Your model number can be found on a sticker beneath the
swing motor. Payment must accompany your order.
Parts List:
Price:**
Motor unit ..................................... $25.00
Plastic seat ................................... $21.00
Side-button hanger tube (right)* ... $13.00
Side-button hanger tube (left)* ..... $13.00
Front-button hanger tube* ............ $13.00
Vinyl seat cover ............................ $13.00
Cloth seat cover ........................... $14.00
Seat belt with buckle .................... $ 5.00
Hardware ...................................... $ 5.00
Plastic leg brace ........................... $ 5.00 (each)
Adjustment wire ............................ $ 7.00
Upper leg section ......................... $ 7.00 (each)
Lower leg section ......................... $ 7.00 (each)
Leg tips (set of four) ..................... $ 5.00
Toy bar kit ..................................... $ 7.00
d
* On certain models.
** Prices subject to change without notice.
IF YOU NEED HELP
r
If you have any questions, please call toll-free:
1-800-345-4109
Return the form below with payment to:
GRACO CHILDREN’S PRODUCTS INC.
CUSTOMER SERVICE DEPARTMENT
P.O. BOX 100, MAIN STREET
T
ELVERSON, PA 19520
Model Number SHIP TO:
(Must be filled in)
Name
ht
Motor unit
Plastic seat
Address
anger
Side button h
tube (right)
Side button h
tube (left)
anger
City, State, Zip
hanger tube
Front button
(
)
Vinyl seat cover
Cloth seat cover
Seat belt with buckle
Hardware
Plastic leg brace
Adjustment wire
Upper leg section
Lower leg section
Leg tips
g
Telephone
Check enclosed
(payable to Graco Children’s
Products Inc.)
Charge to credit card:
Visa
Toy bar kit
MasterCard
Discover
Total:
Shipping
& handling:
$5.00 Account #:
6% sales tax
(PA only):
Expiration date:
Signature:
Total amount
due:
11
|